Sends ESC i d (specify margin amount) with the given number of dots. Without
the option nothing changes: the printer keeps its default of 14 dots.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
When more than one printer is connected, ptouch-print used the first
one it found. --serial <serial> now uses only the printer with that USB
serial number, and --list-connected lists the connected printers with
their serials.
libptouch gets ptouch_open_serial() and ptouch_list_connected();
ptouch_open() keeps its signature and calls ptouch_open_serial() with
NULL. The serial is checked before the P-Lite and unsupported-raster
checks, so a different printer in the wrong mode no longer ends the
search, and the "found on USB bus" line now shows the serial. The early
error returns in the open loop now free the device list.
The PT-E560BT stays busy about 2.2 s after even an 8 mm label, so the
1 second default timeout cannot succeed on a job sent straight after
another: printing five chained labels gives a strip carrying three of
them. ptouch-print reports the timeout and exits non-zero correctly every
time, but no amount of waiting helps when the default is below the
printer's fixed overhead.
Add a trailing min_timeout to the device table. Every other row keeps its
initialiser and gets 0, which resolves to the old default of 1; only the
E560BT carries a value. An explicit --timeout always wins.
Raising the global default would also be defensible: ptouch_getstatus()
returns as soon as the status arrives, measured 0.13 s with --timeout 30
against 0.14 s with --timeout 1, so a higher ceiling costs nothing on a
printer that is ready. But that is a judgement about printers I do not
have, so this keeps it to the one that was measured.
On macOS with Homebrew's argp-standalone, Findargp's link test for
argp_parse fails with an undefined strchrnul, because libargp.a itself
references that GNU extension and the platform has none. The module then
stops with "does not have a symbol named argp_parse", which is not what
is wrong.
Probe for strchrnul first (with _GNU_SOURCE, so glibc answers correctly).
Where it exists, the test is unchanged. Where it is missing, run the same
argp_parse test with a local definition of strchrnul, and have ptouch-print
supply that definition for the real build.
On glibc nothing changes: the probe finds strchrnul and the original test
runs. Checked on Debian stable in the same session.
On the PT-P900W the print area is not centered on the 560-pin printhead:
its center sits at pin 272 rather than the head center (pin 280), a fixed
8-pin offset that is constant across all tape widths. Centering the raster
data on the head therefore prints ~0.5mm off-center (measured as a constant
~1mm margin delta across 12/18/36mm tapes, confirmed against the spec).
Add a pin_offset field to _pt_dev_info (0 = centered, the default for all
existing printers) and apply it in print_img. Set it to -8 for the
PT-P900Wc, which reproduces the spec left-margin exactly for every tape
width ((560-print_area)/2 - 8 = documented left margin).
Reference: Brother "Software Developer's Manual - Raster Command Reference,
PT-P900/P900W/P950NW", section 2.3.5 "Raster line" (per-tape left/right
margin and print-area pin counts for the 560-pin head).
https://download.brother.com/welcome/docp100407/cv_ptp900_eng_raster_102.pdf
Odd behavior in testing with my PT-H500: When printing with precut, and then printing the next label without precut, the next label still gets a precut. i.e. the label with the precut flag gets cut on both ends, even if the next label does not have this flag. The label after that works as expected.
I'm unsure if this is printer behavior or if it could be resolved by sending additional commands somehow (maybe resetting the flag).